MATERIAL SAFETY DATA SHEET
(Complies with OSHA Communication Standard 29CFR 1910.1200 Dept. of Labor.)
CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Osborn 76290TM1206B Gasket and Paint Remover
Revision Date:
2/8/02MANUFACTURER/SUPPLIER'S/NAME:
Osborn International, 5401 Hamilton Ave., Cleveland, OH 44114 (330) 467-4195
COMPOSITION/INFORMATION ON INGREDIENTS
PRODUCT COMPOSITION/ ACGIH TLV OSHA PEL
CAS REG NO. WGT. % TWA STEL TWA STEL UNITS
Methylene Chloride
75-09-2
60-70 50 NA 25 125 ppmPropane\Isobutane\n-Butane
74-98-6
20-30 1000 Asphyxiant 1000 Asphyxiant ppmMethanol
67-56-1
1-10 200 skin 250 200 NA ppmAdditional Component Information:
NA
HAZARDS IDENTIFICATION
HEALTH HAZARD DATA (ACUTE AND CHRONIC)
May cause dizziness or narcosis in high vapor concentrations. Will cause defatting of skin. Effects are reversible. Long term exposure (years) to high concentrations of vapor may cause lung, liver or kidney damage. The solvents listed have been reported to affect the central nervous system. Aspiration hazard if swallowed. Eye and skin irritant. May irritate respiratory tract. Deliberately concentrating and inhaling the vapor of the contents may be harmful or fatal.
OTHER:
Absorption through the skin is possible. Eye irritation may be severe. May cause cardiac abnormalities. Methanol may cause blindness or death if swallowed. Methylene chloride will have an effect on the cardiovascular system.
CARCINOGENICITY:
Inhalation of high concentrations of Methylene Chloride vapor over long periods of time has caused cancer in laboratory animals.
FIRST AID
Give oxygen. Do not induce vomiting. Wash eyes and skin with water for 15 minutes. Get medical help. Never administer adrenalin following overexposure.
ROUTES OF ENTRY
Ingestion, Inhalation, Skin
SIGNS AND SYMPTOMS OF OVEREXPOSURE_
Inhalation - Difficulty in breathing. Skin - redness. Ingestion - vomiting.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE:_
Heart Disease, Respiratory Disorders alcoholism, liver and kidney disease, lung disease, anemia, rhythm disorders of the heart.
PHYSICAL AND CHEMICAL PROPERTIES
Boiling Point
-40F to 148FVapor Pressure at 70F
60VAPOR DENSITY (AIR=1)
4.0EVAP. RATE(BUTYL ACETATE=1)
>1SPECIFIC GRAVITY (WATER=1) The ratio of the weight of a volume of material to the weight of an equal volume of water. Usually expressed as greater than one (>1).
0.9Solubility
NilAppearance Clear
Odor Solvent
PH: Not Applicable
STABILITY AND REACTIVITY
STABILITY:
STABLEINCOMPATIBILITY:-
Strong oxidizers strong alkalies reactive metals aluminum oxygen, nitrogen peroxide, sodium, potassiumHAZARDOUS THERMAL DECOMPOSITION/COMBUSTION PRODUCTS:- Carbon dioxide. Chlorine. Hydrogen chloride. Phosgene.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR
REGULATORY INFORMATION
CALIFORNIA PROPOSITION 65:
WARNING: This product contains a chemical known to the State of California to cause cancer.
Ozone Depleting Substances:
None
HMIS:
FLAMMABILITY 4 , REACTIVITY 0 , HEALTH 3
NFPA:
FLAMMABILITY 4 , REACTIVITY 0 , HEALTH 2
SARA 313 TITLE III - TOXIC CHEMICALS LIST:
Methanol (CAS 67-56-1) Methylene Chloride (CAS 75-09-2)
DOT Shipping Name:
Consumer Commodity, ORM-D
CONTROL MEASURES
Respiratory Protection Equipment
Use NIOSH approved respirator if TLV limit is exceeded.
VENTILATION:
Local exhaust - yes
PROTECTIVE GLOVES:
Use Viton or 4H gloves.
EYE AND FACE PROTECTION:
Chemical goggles or face shield.
OTHER PROTECTIVE EQUIPMENT:
Long Sleeves and Long pants
SAFE HANDLING
Do not smoke while using. Wash hands after use.
PRECAUTIONS FOR SAFE HANDLING AND USE
Flash Point
-142F TCCLOWER EXPLOSION LIMIT : 1.8
UPPER EXPLOSION LIMIT : 9.5
EXTINGUISHING MEDIA:- Water fog, carbon dioxide, foam, dry chemical
UNUSUAL FIRE AND EXPLOSION HAZARDS:-
Heated cans may burst.SPECIAL FIRE FIGHTING PROCEDURES
Keep containers cool. Use equipment or shielding required to protect against bursting or venting containers.SPILL PROCEDURES:_
Use absorbent sweeping compound to soak up material. Put into container. Dispose as hazardous waste.WASTE DISPOSAL METHODS:_
Dispose as hazardous waste in accordance with EPA RCRA.PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: This section contains precautions for general handling and storage of this particular material. This section is generally for SPBD customers; although the statements should generally apply for internal use as well. Any in-plant rules or procedures should take priority over these handling and storage precautions.
Keep away from heat, sparks, or open flame. Store at temperatures below 120F.OTHER INFORMATION:
When spraying more than one half can continuously or more than one can consecutively, use NIOSH approved respirator.NFPA 30B Level:
1